Xantrex PP-SW4048/S 4.0kVA-48vdc Input, 120vac 60hz
Xantrex PP-SW4048/S Power Panel
Finally a Low Cost Alternative to Assembling Components in the Field
The Xantrex PP-SW4048/S Power Panels are less expensive than an on-site component installation and meet many power application needs. To install a Xantrex PP-SW4048/S Power Panel, simply connect them to the battery, PV and or AC loads. The Xantrex PP-SW4048/S Power Panels include inverters and are assembled in the factory with components specified by the dealer or customer.
Included in all Power Panel Systems:
- Powder-coated steel backplate prewired with all NEC/UL requiredAC and DC overcurrent protection and disconnects (only for indoorinstallation). Simply connect to the battery and AC loads and yoursystem is operational.
- Can be used with wind, solar, or hydro DC charging sources
- 60 amp AC system bypass that allows inverter servicing while keeping AC loads connected to the grid or generator
- ETL listed components and enclosure
- Negative/ground bonding block
Options
- Optional nonmetallic battery enclosure which doubles as a shipping enclosure
- Single or dual C40 Charge controllers for solar, wind, hydro DC charging sources
- Flexible conduit for connection of the system to the battery enclosure
- One or two Xantrex SW or DR inverters
SW Series Power Panels
- Sine wave AC power inverter with high-efficiency, bidirectional operation
- Up to 11 kW of continuous AC power
- Up to 60 amps of AC input from a generator or utility grid
- Three-stage, temperature-compensated battery charging
(up to 240A at 24 VDC, and 150A at 48 VDC) - Utility-interactive and generator-support operating modes
- Able to regulate up to 4.8 kW of power from solar or other DC charging sources
- Available outputs of 105, 120, 230 or 120/240 vac at 50 or 60 Hz.
- Available for a 12-, 24- or 48-volt DC system
SW Series Specifications
SW Series Power Panel Systems
The SW Power Panel system comes ready for installation, pre-wired with the following:
- SW Series sinewave AC power inverter with high efficiency and bi-directional operation, includes:
- 60 amp AC pass-thru power at 120 VAC (/S=Single System) or 120/240 VAC (/D=Dual System)
- Adjustable three stage, temperature compensated battery charging - 175 or 250 amp DC disconnect breaker*
- 60 amp AC disconnect/bypass breaker in box*
- AC and DC wiring in conduit (battery cables not included)*
- Powder coated steel back-plate (40" H x 43" W x 1" D)
- Battery Temperature Sensor*
- Inverter Conduit Box*
- Negative/Ground Bonding Block
- 500 amp/50 mV shunt (for remote metering)
*These items are doubled on /D (Dual=two inverters) systems
| Power Panel | Inverter(s) | Power | DC Input | Min Cable** | VAC Output | Charger(s) |
| PP-SW4024S | SW4024 | 4.0 KW | 24 VDC | 4/0 AWG | 120 @ 60 hz | 120 amps |
| PP-SW4024/D | SW4024 x 2 | 8.0 KW | 24 VDC | 4/0 AWG x 2 | 120/240 @ 60 hz | 120 amps x 2 |
| PP-SW3024E/S | SW3024E | 3.3 KW | 24 VDC | 4/0 AWG | 230 @ 50 hz | 100 amps |
| PP-SW3048E/S | SW3048E | 3.3 KW | 48 VDC | 2/0 AWG | 230 @ 50 hz | 50 amps |
| PP-SW4048/S | SW4048 | 4.0 KW | 48 VDC | 2/0 AWG | 120 @ 60 hz | 60 amps |
| PP-SW4048/D | SW4048 x 2 | 8.0 KW | 48 VDC | 2/0 AWG x 2 | 120/240 @ 60 hz | 60 amps x 2 |
| PP-SW4548E/S | SW4548E | 4.5 KW | 48 VDC | 2/0 AWG | 230 @ 50 hz | 57 amps |
| PP-SW5548/S | SW5548 | 5.5 KW | 48 VDC | 4/0 AWG | 120 @ 60 hz | 70 amps |
| PP-SW5548/D | SW5548 x 2 | 11.0 KW | 48 VDC | 4/0 AWG x 2 | 120/240 @ 60 hz | 70 amps x 2 |
Also Known As:
PP.SW4048/S
PP SW4048/S
PP_SW4048/S
PPSW4048/S