Xantrex PP-DR1524/S 1.5kVA-24vdc Input, 120vac 60hz
Xantrex PP-DR1524/S Power Panel
Finally a Low Cost Alternative to Assembling Components in the Field
The Xantrex PP-DR1524/S Power Panels are less expensive than an on-site component installation and meet many power application needs. To install a Xantrex PP-DR1524/S Power Panel, simply connect them to the battery, PV and or AC loads. The Xantrex PP-DR1524/S Power Panels include inverters and are assembled in the factory with components specified by the dealer or customer.
Included in all Power Panel Systems:
- Powder-coated steel backplate prewired with all NEC/UL requiredAC and DC overcurrent protection and disconnects (only for indoorinstallation). Simply connect to the battery and AC loads and yoursystem is operational.
- Can be used with wind, solar, or hydro DC charging sources
- 60 amp AC system bypass that allows inverter servicing while keeping AC loads connected to the grid or generator
- ETL listed components and enclosure
- Negative/ground bonding block
Options
- Optional nonmetallic battery enclosure which doubles as a shipping enclosure
- Single or dual C40 Charge controllers for solar, wind, hydro DC charging sources
- Flexible conduit for connection of the system to the battery enclosure
- One or two Xantrex SW or DR inverters
DR Series Power Panels
- Modified sine wave AC power inverter with high-efficiency operation and battery charging ability
- Up to 7.2 kW of continuous AC power (120/240-VAC systems)
- 30 amps of AC pass through power at 120- or 120/240-VAC from agenerator or utility grid to your loads, in addition to the chargerdraw
- Three-stage, temperature-compensated battery charging - up to 240A at 12 VDC or 140A ;at 24 VDC
- Able to regulate up to 2.4 kW of power from solar or other DC charging sources
- Available outputs of 105, 120, 230 or 120/240 vac at 50 or 60 Hz
- Available for 12- or 24-volt DC system
DR Series Specifications
DR Series Power Panel Systems
The DR Power Panel system comes ready for installation, pre-wired with the following:
- DR Series modified sinewave AC power inverter with high efficiency operation, includes:
- 30 amp AC pass-thru power at 120 VAC (/S=Single System) or 120/240 VAC (/D=Dual System)
- Adjustable three stage, temperature compensated battery charging - 175 or 250 amp DC disconnect breaker*
- 60 amp AC disconnect/bypass breaker in box*
- AC and DC wiring in conduit (battery cables not included)*
- Powder coated steel back-plate (40" H x 43" W x 1" D)
- Battery Temperature Sensor*
- Inverter Conduit Box*
- Negative/Ground Bonding Block
- 500 amp/50 mV shunt (for remote metering)
*These items are doubled on /D (Dual=two inverters) systems
| Part No. | Inverter(s) | Power | DC Input | Min Cable** | VAC Output | Charger |
| PP-DR1512/S | DR1512 | 1.5 KW | 12 VDC | 2/0 AWG | 120 @ 60 hz | 70 amps |
| PP-DR1512/D | DR1512 x 2 | 3.0 KW | 12 VDC | 2/0 AWG x 2 | 120/240 @ 60 hz | 70 amps x 2 |
| PP-DR1512E/S | DR1512E | 1.5 KW | 12 VDC | 2/0 AWG | 230 @ 50 hz | 70 amps |
| PP-DR1524/S | DR1524 | 1.5 KW | 24 VDC | 2/0 AWG | 120 @ 60 hz | 35 amps |
| PP-DR1524/D | DR1524 x 2 | 3.0 KW | 24 VDC | 2/0 AWG x 2 | 120/240 @ 60 hz | 35 amps x 2 |
| PP-DR1524E/S | DR1524E | 1.5 KW | 24 VDC | 2/0 AWG | 230 @ 50 hz | 35 amps |
| PP-DR2412/S | DR2412 | 2.4 KW | 12 VDC | 4/0 AWG | 120 @ 60 hz | 120 amps |
| PP-DR2412/D | DR2412 x 2 | 4.8 KW | 12 VDC | 4/0 AWG x 2 | 120/240 @ 60 hz | 120 amps x 2 |
| PP-DR2424/S | DR2424 | 2.4 KW | 24 VDC | 2/0 AWG | 120 @ 60 hz | 70 amps |
| PP-DR2424/D | DR2424 x 2 | 4.8 KW | 24 VDC | 2/0 AWG x 2 | 120/240 @ 60 hz | 70 amps x 2 |
| PP-DR2424E/S | DR2424E | 2.4 KW | 24 VDC | 2/0 AWG | 230 @ 50 hz | 70 amps |
| PP-DR3624/S | DR3624 | 3.6 KW | 24 VDC | 4/0 AWG | 120 @ 60 hz | 70 amps |
| PP-DR3624/D | DR3624 x 2 | 7.2 KW | 24 VDC | 4/0 AWG x 2 | 120/240 @ 60 Hz | 70 amps x 2 |
Also Known As:
PP.DR1524/S
PP DR1524/S
PP_DR1524/S
PPDR1524/S